Language can be tricky. Especially if it is in your
second or third language.
:)
--- Victor Cappuccio <victor@xxxxxxxxxxxxxx> wrote:
> Thanks Brian, I thought it also, but since the
> original question says
> "> automatically after some seconds (Not minutes)"
>
> R1(config-line)#absolute-timeout ?
> <0-10000> Absolute timeout interval in minutes
>
>
> thanks,
> Victor Cappuccio.-
> - CCSI# 31452
>
> Network Learning Inc - A Cisco Sponsored
> Organization (SO) YES! We take
> Cisco Learning credits!
> victor@xxxxxxxxxxxxxx
> http://www.ccbootcamp.com (Cisco Training and Rental
> Racks)
> http://www.ccbootcamp.com/groupstudy.html
> (groupstudy member discounts!)
> Voice: 702-968-5100
> FAX: 702-446-8012
>
>
>
> -----Original Message-----
> From: Brian Dennis
> [mailto:bdennis@xxxxxxxxxxxxxxxxxxxxxx]
> Sent: Fri 6/8/2007 17:11
> To: Victor Cappuccio; Adham Ali;
> ccielab@xxxxxxxxxxxxxx
> Subject: Re: Telnet Absolute Timeout! [mx]
>
> Victor,
> That command is used to determine how long a TCP
> session will wait to reach
> the established state. The question was in regards
> to how to close a telnet
> session using an absolute timeout. The command is
> "absolute-timeout
> <seconds>" under the line configuration.
>
> HTH,
>
> Brian Dennis, CCIE4 #2210 (R&S/ISP-Dial/Security/SP)
> bdennis@xxxxxxxxxxxxxxxxxxxxxx
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987
> Direct: 775-745-6404 (Outside the US and Canada)
>
>
>
>
> On 6/8/07 4:46 PM, "Victor Cappuccio"
> <victor@xxxxxxxxxxxxxx> wrote:
>
> > Hi,
> >
> > R1(config)#ip tcp synwait-time ?
> > <5-300> Wait time
> >
> >
> > Just put 5
> >
> >
> > thanks,
> > Victor Cappuccio.-
> > - CCSI# 31452
> >
> > Network Learning Inc - A Cisco Sponsored
> Organization (SO) YES! We take
> > Cisco Learning credits!
> > victor@xxxxxxxxxxxxxx
> > http://www.ccbootcamp.com (Cisco Training and
> Rental Racks)
> > http://www.ccbootcamp.com/groupstudy.html
> (groupstudy member discounts!)
> > Voice: 702-968-5100
> > FAX: 702-446-8012
> >
> >
> >
> > -----Original Message-----
> > From: nobody@xxxxxxxxxxxxxx on behalf of Adham Ali
> > Sent: Fri 6/8/2007 16:45
> > To: ccielab@xxxxxxxxxxxxxx
> > Subject: Telnet Absolute Timeout!
> >
> > Dear All,
> >
> > Does anybody know how can i make a telnet
> session to a router be closed
> > automatically after some seconds (Not minutes) and
> the session closure
> should
> > be done evenif the session isn't idle?!!!
> >
> >
> > Waiting for relies!!
> >
> > Regards,
> > Adham.
> >
> >
> > ---------------------------------
> > No need to miss a message. Get email on-the-go
> > with Yahoo! Mail for Mobile. Get started.
> >
> >
>
_______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
>
_______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
_______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
