GroupStudy.com GroupStudy.com - A virtual community of network engineers
 Home  BookStore  StudyNotes  Links  Archives  StudyRooms  HelpWanted  Discounts  Login
Re: LAB1.V3.Volume1 posted 02/11/2007
[Chronological Index] [Thread Index] [Top] [Date Prev][Date Next] [Thread Prev][Thread Next]


Mohamed,

Cisco has reported this as OSPF Bug ID: CSCse72792

"OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
networks"

*Symptom:*

Can't configure OSPF static neighbor


*Conditions:*

Virtual Link is configured.


*Workaround:*

There is no known workaround


HTH
Victor.-



> Tandou Mohamed wrote:
> > GS,
> >   When I configured  ip pim sparse-dense-mode under my interface i get
> this errors message below.
> >
> >   interface config:
> >
> >   "interface FastEthernet0/0
> >  ip address 183.1.2.2 255.255.255.0
> >  ip pim sparse-dense-mode
> >  duplex auto
> >  speed auto
> >  no keepalive
> >
> >   ================================================================
> >   Errors message:
> >
> >   Mar  7 09:06:15.440: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on
> this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 224
> > Rack1R2#
> > Mar  7 09:07:15.441: %MROUTE-3-NO_PIM_NBR: There is no PIM neighbor on
> this IDB: FastEthernet0/0 -Process= "PIM Process", ipl= 0, pid= 224
> >
> >   ===============================================================
> >   i investigated the errors message according to cisco it says:
> >   %MROUTE-3-NO_PIM_NBR : There is no PIM neighbor on this IDB: [chars]
> >   Explanation    There is no PIM neighbor on the specified IDB. The most
> probable cause of this error is that PIM is not configured correctly on this
> interface or on interfaces of the next-hop routers.
> >
> >   ==============================================================
> >   The lab said configure PIM on R2, R3 and R5. i don't get the error on
> R3 and R5 but only R2
> >
> >   ==============================================================
> >
> >   Task 3.2 requested to configure OSPF area 45 on VLAN 45 between R4 and
> R5 when i checked the solution they have:
> >
> >   R4
> >   interface FastEthernet0/0
> >  ip address 183.1.45.4 255.255.255.0
> >  ip ospf network non-broadcast
> >
> >   router ospf 1
> > network 183.1.45.5 0.0.0.5 area 45
> >   neighbor 183.1.45.5
> >
> >   When i tried to simulate what they have i am getting this errors
> message:
> >
> >   Rack1R4(config)#router ospf 1
> > Rack1R4(config-router)#nei
> > Rack1R4(config-router)#neighbor 183.1.45.5
> > OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> networks
> > Rack1R4(config-router)#
> >
> >   i removed the ospf process and reapplied still getting the same error
> message
> >
> >   Any idea?
> >
> >   Thanks,
> >   Mohamed
> >
> >
> >
> > ---------------------------------
> > Looking for earth-friendly autos?
> >  Browse Top Cars by "Green Rating" at Yahoo! Autos' Green Center.
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html