GroupStudy.com GroupStudy.com - A virtual community of network engineers
 Home  BookStore  StudyNotes  Links  Archives  StudyRooms  HelpWanted  Discounts  Login
Re: router booting up problem , help me posted 11/27/2006
[Chronological Index] [Thread Index] [Top] [Date Prev][Date Next] [Thread Prev][Thread Next]


Thank you for help  !!!!

Regards,

On 11/27/06, Dan C <cdan2154@xxxxxxxxx> wrote:
>
> Hello there,
>
> I am happy to see you back up and running. xmodem -r will load the image
> into dram more info at :
>
>
> http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a008015bfac.shtml
>
> Cheers,
> Dan
>
> On 11/26/06, cisco monster < cisco.monster@xxxxxxxxx> wrote:
> >
> > Thanx bro , would u tell me how can i load IOS in dram , actually i have
> > recoverd my router using Xmode thank god flash is not dead !!!! i want to
> > know how to load IOS in dram
> >
> > Regards
> >
> > On 11/26/06, Dan C <cdan2154@xxxxxxxxx> wrote:
> > >
> > > Hi,
> > >
> > > Do you have any flash cards? If not you may need to use xmodem
> > > commands to reformat the internal flash and copy across a new image. Also,
> > > if your internal flash is dead, you can load your image right into DRAM till
> > > you replace the faulty flash, however the router will lose that image on
> > > reload.
> > >
> > > Cheers,
> > > Dan
> > >
> > > On 11/26/06, cisco monster < cisco.monster@xxxxxxxxx> wrote:
> > > >
> > > > Yes its already working , its 3640 with 32MB flash n 128MB dram
> > > >
> > > > rommon 8 > meminfo
> > > >
> > > > Main memory size: 128 MB in 64 bit mode.
> > > > Available main memory starts at 0xa000e000, size 131016KB
> > > > IO (packet) memory size: 15 percent of main memory.
> > > > NVRAM size: 128KB
> > > >
> > > >
> > > > rommon 9 > dev
> > > > Devices in device table:
> > > >         id  name
> > > >     flash:  flash
> > > >     slot0:  PCMCIA slot 0
> > > >     slot1:  PCMCIA slot 1
> > > >     eprom:  eprom
> > > >
> > > > I think either flash: or IOS has crashed !!!
> > > >
> > > > Regards
> > > >
> > > > On 11/25/06, Dan C < cdan2154@xxxxxxxxx> wrote:
> > > > >
> > > > > Hello there,
> > > > >
> > > > > Few questions:
> > > > > did it work before or this is a new install ?
> > > > > what platform is it?
> > > > > Once in rommon do the following:
> > > > > meminfo --- to check if your main memory is fine and enough for
> > > > > your ios
> > > > > dev    ---- to see on which device router holds your image it may
> > > > > be on internal flash on flash card in slot 0 or 1
> > > > >
> > > > > If you have a valid image try to boot ignoring the start up config
> > > > > file : b <image location>:<image name as seen> or confreg 0x2142 and i or r
> > > > >
> > > > > Cheers,
> > > > > Dan
> > > > >
> > > > > On 11/25/06, cisco monster < cisco.monster@xxxxxxxxx> wrote:
> > > > >
> > > > > > Hello group ,
> > > > > >                     While the router is booting up I'm getting
> > > > > > below err n
> > > > > > it starts in Rommon mode ,
> > > > > >
> > > > > >
> > > > > > get_man_dev: Unknown device - probably NOT formatted.
> > > > > > get_man_dev: Unknown device - probably NOT formatted.
> > > > > > lseek out of bounds
> > > > > > getdirent: lseek error
> > > > > > boot: cannot determine first file name on device "flash:"
> > > > > >
> > > > > > If I m giving commnad dir flash: in rommon mode , then i m
> > > > > > getting
> > > > > >
> > > > > > rommon 1 > dir flash:
> > > > > > get_man_dev: Unknown device - probably NOT formatted.
> > > > > > get_man_dev: Unknown device - probably NOT formatted.
> > > > > >          File size           Checksum   File name
> > > > > > lseek out of bounds
> > > > > > getdirent: lseek error
> > > > > >
> > > > > > So is it error of flash: or  IOS is gonna crashed ? plz help me
> > > > > >
> > > > > > Regards
> > > > > >
> > > > > >
> > > > > > _______________________________________________________________________
> > > > > > Subscription information may be found at:
> > > > > > http://www.groupstudy.com/list/CCIELab.html