Russell,
Yes, for Cell Mode MPLS. The configuration is very short and
straightforward so it wouldn't warrant buying an LS1010 unless you
already have access to one.
HTH,
Brian McGahan, CCIE #8593
bmcgahan@xxxxxxxxxxxxxxxxxxxxxx
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987 x 705
Outside US: 775-826-4344 x 705
24/7 Support: http://forum.internetworkexpert.com
Live Chat: http://www.internetworkexpert.com/chat/
> -----Original Message-----
> From: Russell Kelly (rukelly) [mailto:rukelly@xxxxxxxxx]
> Sent: Friday, September 29, 2006 11:34 AM
> To: Brian McGahan; Tony Schaffran; ccielab@xxxxxxxxxxxxxx
> Subject: RE: ATM Topology Required For SP Lab
>
> Thanks Brian,
>
> - I used to see the back to back with the old R&S labs (well some of
> them) and was wondering if the SP (the new owner of ATM) called for
just
> this, or more - I assume for MPLS et al the new SP IE wkbk will call
for
> an ATM switch then? :-)
>
> Ta
> R
>
>
> -----Original Message-----
> From: Brian McGahan [mailto:bmcgahan@xxxxxxxxxxxxxxxxxxxxxx]
> Sent: 29 September 2006 15:07
> To: Tony Schaffran; Russell Kelly (rukelly); ccielab@xxxxxxxxxxxxxx
> Subject: RE: ATM Topology Required For SP Lab
>
> To run cell mode MPLS you need an MPLS aware ATM switch such as
> the LS1010. If you just want to do basic PVCs when you can run ATM
back
> to back.
>
> HTH,
>
> Brian McGahan, CCIE #8593
> bmcgahan@xxxxxxxxxxxxxxxxxxxxxx
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987 x 705
> Outside US: 775-826-4344 x 705
> 24/7 Support: http://forum.internetworkexpert.com
> Live Chat: http://www.internetworkexpert.com/chat/
>
>
> > -----Original Message-----
> > From: nobody@xxxxxxxxxxxxxx [mailto:nobody@xxxxxxxxxxxxxx] On Behalf
> Of
> > Tony Schaffran
> > Sent: Friday, September 29, 2006 8:42 AM
> > To: 'Russell Kelly (rukelly)'; ccielab@xxxxxxxxxxxxxx
> > Subject: RE: ATM Topology Required For SP Lab
> >
> > You cannot configure any kind of SVC with a back-to-back ATM
> connection
> > between two routers.
> >
> > There is probably more you cannot do, but that one is pretty
> significant.
> >
> > Tony Schaffran
> > Network Analyst
> > CCIE #11071
> > CCNP, CCNA, CCDA,
> > NNCDS, NNCSS, CNE, MCSE
> >
> > www.cconlinelabs.com
> > Your #1 choice for online Cisco rack rentals.
> >
> >
> >
> > -----Original Message-----
> > From: nobody@xxxxxxxxxxxxxx [mailto:nobody@xxxxxxxxxxxxxx] On Behalf
> Of
> > Russell Kelly (rukelly)
> > Sent: Friday, September 29, 2006 3:29 AM
> > To: ccielab@xxxxxxxxxxxxxx
> > Subject: ATM Topology Required For SP Lab
> >
> >
> > Hi All,
> >
> > Just looking for some advice on the ATM topology required for the SP
> > workbooks (upcoming for ie) and the ipexpert SP workbook. It looks
> like
> > I cold get away with a back-to-back ATM connection without the need
> for
> > an LS1010 or the like. Is this the case - has someone set this up
> > recently who could help out?
> >
> > Cheers
> >
> >
>
_______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
>
_______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
