Ademola,
Could you send your configs? Did you disable RIP on the ethernets?
Chuck
-----Original Message-----
From: nobody@xxxxxxxxxxxxxx [mailto:nobody@xxxxxxxxxxxxxx]On Behalf Of
Ademola Osindero
Sent: Friday, September 28, 2001 3:27 AM
To: ccielab@xxxxxxxxxxxxxx
Subject: Another IPX issue
All,
I am working on customizing IPX service information exchange and found out
this hitch(may be I am wrong somewhere) while trying to verify the
difference between ipx sap-incremental eigrp <as> and ipx sap-incremental
eigrp <as> rsup-only.
My scenario consists of r1 and r4 with the following ipx interface
addresses
r1#sh ipx int brief
Interface IPX
Network Encapsulation Status IPX State
Ethernet0 1 NOVELL-ETHER up [up]
Loopback0 unassigned not
config'd up n/a
Loopback1 unassigned not
config'd up n/a
Loopback2 unassigned not
config'd up n/a
Loopback3 unassigned not
config'd up n/a
Serial0 10 HDLC up
[up]
Serial1 unassigned not
config'd administratively down n/a
r4#sh ipx int brief
Interface IPX
Network Encapsulation Status IPX State
Ethernet0 unassigned not
config'd up n/a
Ethernet0.1 21 NOVELL-ETHER up [up]
Ethernet0.2 unassigned not
config'd up n/a
Loopback0 unassigned not
config'd up n/a
Loopback1 unassigned not
config'd up n/a
Loopback2 unassigned not
config'd up n/a
Loopback9 9 UNKNOWN up
[up]
Loopback10 unassigned not
config'd up n/a
Serial0 20 FRAME-RELAY up
[up]
Serial1 10 HDLC up
[up]
I intend to allow only incremental sap updates on e0 and s0 on r1 and e0.1
and s1 on r4 so I did these;
i. Enabled IPX EIGRP and included the serial and ethernet interfaces' ipx
networks
ii. Configured ipx sap-incremental eigrp 1 on the interfaces
and the result
on r1:
1w1d: IPXSAP: positing update to 1.ffff.ffff.ffff via Ethernet0 (broadcast)
(full)
1w1d: IPXSAP: Update type 0x2 len 160 src:1.0060.5cf3.b568
dest:1.ffff.ffff.ffff (452)
1w1d: type 0x7, "printsrv", 9.0000.0003.0004(453), 2 hops
1w1d: type 0x4, "filesrv", 9.0000.0003.0003(452), 2 hops
on r4:
IPXSAP: positing update to 21.ffff.ffff.ffff via Ethernet0.1 (broadcast)
(full)
IPXSAP: Update type 0x2 len 224 src:21.0000.0c3e.2534
dest:21.ffff.ffff.ffff(452)
type 0x4, "route1srv", 1.0000.0001.0001(452), 1 hops
type 0x7, "printsrv", 9.0000.0003.0004(453), 2 hops
type 0x4, "filesrv", 9.0000.0003.0003(452), 2 hops
IPXSAP: positing update to 9.ffff.ffff.ffff via Loopback9 (broadcast) (full)
IPXSAP: Update type 0x2 len 96 src:9.0000.0001.0004
dest:9.ffff.ffff.ffff(452)
type 0x4, "route1srv", 1.0000.0001.0001(452), 1 hops
IPXSAP: positing update to 20.ffff.ffff.ffff via Serial0 (broadcast) (full)
Full SAP updates are still been advertised on the ethernet interfaces
although they are suppressed on the serial interfaces.
Has anyone an idea on what is wrong? I haven't included rsup-only on my
config yet (still battling on suppressing updates).
Thanks
Osindero Ademola
Schlumberger Network Solutions
Tel: 234 1 261 0446 Ext 3227
Fax 234 1 262 1034
email:osindero@xxxxxxxxxxxxxxxxx
**Please read:http://www.groupstudy.com/list/posting.html
**Please read:http://www.groupstudy.com/list/posting.html
_______________________________________________________
To unsubscribe from the CCIELAB list, send a message to
majordomo@xxxxxxxxxxxxxx with the body containing:
unsubscribe ccielab
