TRRSM (gotta have an acronym) requires 12.0 T. Works fine, thanks to all that responded.
-Tim
At 02:11 PM 9/17/01 -0500, kenneth.mays@xxxxxxxxxxxx wrote:
>Hey Tim,
>
>According to Cisco, you need a 12.0 T image for token ring RSM support.
>
>http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fibm_c/bcfpart1/bcfbrov.htm#xtocid48410
>
>
>- - - - - - - - - - - -
>
>Kenneth Mays
>Sr. Network Analyst
>AutoZone
>Telecomm Dept. 8035
>123 S. Front St.
>Memphis TN 38103
>Office (901) 495-6941
>Fax (901) 495-8300
>
>
>
>
> Tim Fletcher
> <tim@xxxxxxxx To: "Jeff K." <jeffbk@xxxxxxxxxxxxx>, <ccielab@xxxxxxxxxxxxxx>
> il.net> cc:
> Sent by: Subject: Re: Cat 5000 w/RSM & Token Ring
> nobody@xxxxxx
> tudy.com
>
>
> 09/17/2001
> 12:24 PM
> Please
> respond to
> Tim Fletcher
>
>
>
>
>
>
>Yes, "sh vlan" included below. The problem is that the RSM does not seem to
>
>recognize the type parameter
>
>Router(config)#int vlan 100 ?
> <cr>
>
>Does anybody have a working config? If so, please let me know what versions
>
>you are using.
>
>Thanks.
>
>-Tim
>
>Output from "sh vlan" on sup:
>
>VLAN Name Status IfIndex Mod/Ports, Vlans
>---- -------------------------------- --------- -------
>------------------------
>1 default active 5 3/3-6,3/8-24
>2 VLAN0002 active 11 3/1,3/7
>3 VLAN0003 active 12 3/2
>4 VLAN0004 active 59
>10 VLAN0010 active 61 5/1-2
>100 VLAN0100 active 60 10
>1002 fddi-default active 6
>1003 trcrf-default active 9 5/3-16
>1004 fddinet-default active 7
>1005 trbrf-default active 8 1003
>
>
>VLAN Type SAID MTU Parent RingNo BrdgNo Stp BrdgMode Trans1
>Trans2
>---- ----- ---------- ----- ------ ------ ------ ---- -------- ------
>------
>1 enet 100001 1500 - - - - - 0 0
>2 enet 100002 1500 - - - - - 0 0
>3 enet 100003 1500 - - - - - 0 0
>4 enet 100004 1500 - - - - - 0 0
>10 trcrf 100010 4472 100 0xa - - srb 0 0
>100 trbrf 100100 4472 - - 0x1 ibm - 0 0
>1002 fddi 101002 1500 - - - - - 0 0
>1003 trcrf 101003 4472 1005 0xccc - - srb 0 0
>1004 fdnet 101004 1500 - - - - - 0 0
>1005 trbrf 101005 4472 - - 0xf ibm - 0 0
>
>
>VLAN DynCreated RSPAN
>---- ---------- --------
>1 static disabled
>2 static disabled
>3 static disabled
>4 static disabled
>10 static disabled
>100 static disabled
>1002 static disabled
>1003 static disabled
>1004 static disabled
>1005 static disabled
>
>
>VLAN AREHops STEHops Backup CRF 1q VLAN
>---- ------- ------- ---------- -------
>10 7 7 off
>1003 7 7 off
>
>
>At 09:20 PM 9/16/01 -0500, Jeff K. wrote:
>>Have you configured VLAN 100 on the switch first?
>>
>>----- Original Message -----
>>From: "Tim Fletcher" <tim@xxxxxxxxxxxxxx>
>>To: <ccielab@xxxxxxxxxxxxxx>
>>Sent: Sunday, September 16, 2001 7:28 PM
>>Subject: Cat 5000 w/RSM & Token Ring
>>
>>
>> > Hi all,
>> >
>> > I have a Cat 5505 with RSM and WS-X5030 token ring card. The problem is
>I
>>can't get Token Ring vlans to work. All the documentation only seems to
>>address Ethernet vlans. I finally found some information at
>>http://www.cisco.com/univercd/cc/td/doc/product/lan/trsrb2/scen6.htm which
>>uses the syntax "interface vlan100 type trbrf", but my router won't accept
>>that.
>> >
>> > Router(config)#int vlan 100 type trbrf
>> > ^
>> > % Invalid input detected at '^' marker.
>> >
>> > Any ideas?
>> >
>> > -Tim
>> >
>> > Output from "sh ver" on RSM:
>> >
>> > Cisco Internetwork Operating System Software
>> > IOS (tm) C5RSM Software (C5RSM-DSV56I-M), Version 12.0(19), RELEASE
>>SOFTWARE (fc1)
>> > Copyright (c) 1986-2001 by cisco Systems, Inc.
>> > Compiled Tue 07-Aug-01 03:37 by nmasa
>> > Image text-base: 0x60010930, data-base: 0x60CF0000
>> >
>> > ROM: System Bootstrap, Version 11.2(17523) [mohsen 102], INTERIM
>SOFTWARE
>> > BOOTFLASH: C5RSM Software (C5RSM-BOOT-M), Version 12.0(17), RELEASE
>>SOFTWARE (fc1)
>> >
>> > Router uptime is 19 minutes
>> > System restarted by reload
>> > System image file is "slot0:c5rsm-dsv56i-mz.120-19"
>> >
>> > cisco RSP2 (R4700) processor with 65536K/2072K bytes of memory.
>> > R4700 processor, Implementation 33, Revision 1.0
>> > Last reset from power-on
>> > G.703/E1 software, Version 1.0.
>> > G.703/JT2 software, Version 1.0.
>> > X.25 software, Version 3.0.0.
>> > Bridging software.
>> > 1 C5IP controller (2 Vlan).
>> > 2 Virtual Ethernet/IEEE 802.3 interface(s)
>> > 123K bytes of non-volatile configuration memory.
>> >
>> > 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
>> > 20480K bytes of Flash PCMCIA card at slot 1 (Sector size 128K).
>> > 8192K bytes of Flash internal SIMM (Sector size 256K).
>> > Configuration register is 0x2102
>> >
>> >
>> >
>> > Output from "sh mod" on Cat:
>> >
>> > Mod Slot Ports Module-Type Model Sub Status
>> > --- ---- ----- ------------------------- ------------------- ---
>--------
>> > 1 1 2 1000BaseSX Supervisor WS-X5530 yes ok
>> > 2 2 1 Route Switch WS-X5302 no ok
>> > 3 3 24 10BaseT Ethernet WS-X5013 no ok
>> > 5 5 16 Token Ring WS-X5030 no ok
>> >
>> > Mod Module-Name Serial-Num
>> > --- -------------------- --------------------
>> > 1 00010823838
>> > 2 00006776074
>> > 3 00006579490
>> > 5 00007380986
>> >
>> > Mod MAC-Address(es) Hw Fw Sw
>> > --- -------------------------------------- ------ ----------
>-------------
>>----
>> > 1 00-10-0b-1f-34-00 to 00-10-0b-1f-37-ff 2.3 5.1(2) 6.3(1)
>> > 2 00-e0-1e-91-be-5c to 00-e0-1e-91-be-5d 4.5 20.22 12.0(19)
>> > 3 00-10-54-80-4f-c8 to 00-10-54-80-4f-df 1.0 1.1 6.3(1)
>> > 5 00:05:77:05:91:15 to 00:05:77:05:91:25 1.0 3.1(2) 3.3(3)
>> >
>> > Mod Sub-Type Sub-Model Sub-Serial Sub-Hw
>> > --- -------- --------- ---------- ------
>> > 1 NFFC WS-F5521 0008933672 1.0
>> > 1 uplink WS-U5534 0016366617 1.2
>> > **Please read:http://www.groupstudy.com/list/posting.html
>**Please read:http://www.groupstudy.com/list/posting.html
>------------------------------------------------------------------------
>The information transmitted is intended only for the person or entity to
>which it is addressed and may contain confidential and/or privileged
>material. Any review, retransmission, dissemination or other use of, or
>taking of any action in reliance upon, this information by persons or
>entities other than the intended recipient is prohibited. If you received
>this in error, please contact the sender and delete the material from any
>computer.
**Please read:http://www.groupstudy.com/list/posting.html
_______________________________________________________
To unsubscribe from the CCIELAB list, send a message to
majordomo@xxxxxxxxxxxxxx with the body containing:
unsubscribe ccielab
